According to the installation instructions, lowering the exhaust isn't required during the installation of the Draw-Tite # 75678 on a 2010 Transit Connect.
The instructions do call for the spare tire to be lowered to gain access to the frame and then raised back up into position after the install is complete.
Installation of the Tekonsha Custom Fit Vehicle Wiring, part # 118585, is not too bad. The unit simply plugs into the factory connectors of the tail lights on each side of the vehicle... view full answer...
I attached an install video that shows a controller like the P2 part # 90885 being installed on a 2016 Ford Transit Connect just like yours. If you use it as a guide it will walk you through the entire process. The wire color we found to be the correct one for your vehicle is the color purple. view full answer...
Yes. The TracRac TracVan ES Van Ladder Rack - 2 Bar - 500 lbs # TH29611XT, can have the load stops removed as needed. You will however need to remove the end caps to remove them. I recommend using the Loctite Anti-Seize Stick # LT37616 if you will be removing and using them often. view full answer...
Installing a roof vent on a vehicle that has a corrugated roof, especially a smaller vent like the Ventline # VP-543SP which requires a mounting hole only 6-1/2-inches in diameter, will mean that you'll need to fill the gaps between the vent and roof caused by those corrugations.
The easiest way to do this is to use a pure silicone sealant/adhesive such as # 0160297 which is white or a similar product from a local hardware store that is often available in a clear colorless form or in... view full answer...
Great question! I went ahead and called my tech at Rhino-Rack, and she confirmed that the reason why there are two different heights of legs that come with the Rhino-Rack Roof Rack # RLZ01-DC is because of the curvature of the roof. She also said that the crossbars will be even once installed, so the cargo box will lay completely flat. I went ahead and attached a picture of this rack installed to give you perspective.
For a great cargo box that is compatible with the larger Heavy-Duty... view full answer...
Many front-wheel drive vehicles can not be flat-towed so always check the owner's manual for special instructions or suggestions. I looked in the Owner's Manual of your 2016 Ford Transit Connect and it can not be flat-towed because the transmission can be damaged. Instead, your Ford Transit is to be towed with the front wheels off of the ground with a tow dolly like the Roadmaster Tow Dolly, Item # RM-2050-1. Whatever dolly you choose, make sure it has the weight capacity needed to tow... view full answer...
The T-One Vehicle Wiring Harness part # 118585 is a great option for a 2010 Ford Transit Connect and what I recommend using. It does not contain any sort of feature to disable the reverse safety system (RSS) but it will work on models with reverse sensors. This may be an issue while towing with a trailer connected. I wouldn't be able to say for sure so looking in your owner's manual or reaching out to the dealer would be the best option. view full answer...
The Thule TracRac TracVan ES Van Ladder Rack part # TH29611XT which is a fit for your 2015 Ford Transit Connect does not require you to remove the headliner for installation. Instead, there are fixed points on the roof of the Transit Connect with plugs in them. Once the plug are removed you will then place the mounting feet over these holes and then secure them with the included hardware.
I have attached a photo on the above for you to reference. view full answer...
You will not need to drill any holes in your 2014 Ford Transit Connect to install the Curt Hitch part # C12123. Check out the installation instructions I attached for this hitch as well.
For trailer wiring you would want the Curt Wiring Harness part # C56218.
For a ball mount you would want the part # C45521, pin an clip part # F-4, 2 inch ball part # A-82, 1-7/8 inch ball part # A-80. view full answer...
The built-in thermostat of the MaxxAir MaxxFan Trailer Roof Vent # MA00-04000K is what determines the speed of the fan. The user doesn't have direct control over the speed of the fan because you would just set the desired temperature and the fan takes care of the rest.
I have linked a review video that you can check out as well. view full answer...
I'm not 100 percent certain what you mean by "threaded sleeves" but if your have a 2015 Ford Transit Connect with a long wheelbase, you will need to drill holes in your roof in order to attach the Rhino-Rack RT-Style Roof Rack Tracks # RRRTS547, which is what you will mount the rest of the roof rack system to; there are no threaded holes with which to install this rack.
Once the tracks are in place you will complete the installation by adding the Roof Rack Leg Spacer Blocks # RRQMHD05-2,... view full answer...
The Curt Wiring Harness # 56090 supplies a 4-way flat connection point for the trailer connection. The functions of these wires are:
Green - Right Turn and Brake Lights
Yellow - Left Turn and Brake Lights
Brown - Taillights or Running lights
White - Ground
This wiring harness does not provide a wiring option for detection or sending a reverse signal. I have included a link to one of our helpful articles about trailer wiring diagrams and vehicle connectors for your reference.
To disable... view full answer...
The degree of protection from moisture when installing the Ventline Vanair Roof Vent with 12V Fan # VP-543SP will really depend on making seamless contact between the vent's mounting surface and the surfaces on the Transit Connect.
The best install comes from using a flexible pure silicone caulk adhesive, such as white caulk # 0160297. Most hardware stores will offer a pure silicone caulk like this in a range of colors, even clear, so you may be able to source some locally that better... view full answer...
Per the instructions at step 12 for the Rhino-Rack RT-Style Roof Rack Tracks, it states that you should use the pneumatic or concertina style rivet gun because the rivets have to be firmly seated in the tracks.
Using a normal hand rivet gun may not provide enough force to secure the rivets and that would mean removal of the rivets by drilling them out and replacing them. The manufacturer is stressing that the tracks need to be well secured so they recommend the rivet guns that they are... view full answer...
The Curt # C18100 is secured with a pin and clip that makes sure that it stays locked in the upright position when folded up towards the back of the vehicle. Our review video that Randy did, which is linked to this answer, shows you how it operates. You could potentially use a locking hitch pin like the # e98880 but I don't believe it's going to substantially improve the stability over the included hitch pin. view full answer...
You could run wiring in anyway that you like to a "solar generator" or power station, or other device or battery able to provide 12 volts at two amps. You would only need to attach an appropriate plug to match your device outlet.
If you would like to email me the brand and model number of your device I could advise what plug might be needed. Depending on how far away your device is, you may also need some additional cable like etrailer # 10-2-1. view full answer...
Yes, the VanTred Custom Floor Mat for Cargo Vans # VTTC14S is 1/2" thick and designed to protects your van floor from impact damage and scratches, with the though that these will be used in work trucks with heavy tools and materials banging against it.
Since you'll have pets in on this mat you'll be happy to know the the closed-cell construction is waterproof and won't absorb any spills or accidents. It can be easily sprayed down when it's in need of a cleaning as well. view full answer...
Sure, you can install the Trailer Vent # HMAV2-AVT2 facing the rear if you like to cut down the wind noise. And there are drain holes for water at the corners of the vent.
See the red arrow in the accompanying photo? That would be the drain hole for the rain water so it will be able to escape. view full answer...
Dual hitch receivers and adapters like parts # RM-077-8 and # RM-048-8 are meant to be used for flat towing only but I do have a solution for you.
The Gen-Y hitches basically give you additional receivers at varying heights and they can be used for towing and accessories. For your application we have the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers # 325-GH-314. This fits a 2" trailer hitch and offers 7-1/2" of drop/rise. It is rated for 10K towing and 1.5K tongue weight although... view full answer...
A third crossbar can be added to the 2014 Ford Transit Connect, but you will need to purchase a second full 2 bar kit, part # TH29611XT. This will install one bar into the middle set of holes on the roof of your 2014 Ford Transit Connect.
I haven't had any customers reporting use of this system, but I anticipate that you'll get a little more wind noise from the third bar and any accessories you add.
Remember that you'll need to purchase accessories and adapters for a TracRac bar, as... view full answer...
Go To Results